iFlight Chimera7 LR Analog 320mm SucceX-D F7 7 Inch Freestyle FPV Racing Drone
Note: Get a notification from iFlight, currently all their air traffic controllers will come without a barometer .
October 26, 2021.
Introduction:
The iFlight 7 inch long range drone can carry larger batteries to get the flight time to surf the Swiss Alps if you want!
Super stiff frame for minimal resonance and 2806.5 motors for maximum 7 inch propeller control. Fly with large batteries on top or even larger batteries on the bottom, 6 cell recommended or 5 cell for slow driving. But no matter what style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3,000mAh above (slow drive) or 6S 2,500mAh above.
GPS functionality to find your way back and Betaflight GPS Rescue mode ready for setup (OFF by default to prevent unexpected behavior; setup instructions included). Vertical and horizontal TBS Crsf antenna mounts included to cover you and your antenna dead ends.
Features:
- 6mm rigid arm design for more rigidity
- Option for top and bottom battery mounting
- XING 2806.5 efficient wide stator motors
- GPS preinstalled for more safety in the distance
- 800mW high power adjustable VTX
- The TPU floor stand for Gopro Mount is included. (TPU camera mount is NOT included)
- 360° TPU protection, FPV cam protection and antenna mounts
- Battery voltage LED status light (illuminated IF logo below)
Specification:
Brand Name: iFlight
Model: Chimera7 LR Analog
Item name: 320mm F7 4s/6S 7 inch Long Range FPV Racing Drone
Drone Wheelbase: 320mm
Optional KV version: 1300KV (for long range); 1800KV (for freestyle)
Optional receiver version: PNP (without receiver)
TBS CRSF Nano RX (Built-in DJI Receiver & External TBS CRSF Nano Receiver)
Weight: 580.2 g (without battery)
| Chimera7 320mm frame set |
Wheelbase: 320mm Main body dimension: 258*199mm Distance from bottom to top: 20 mm Arm thickness: 6mm Bottom plate thickness: 3mm Cover plate thickness: 2mm Thickness of the top (middle) plate: 3 mm Camera plate thickness: 3mm (TPU inserts included) |
| SucceX-D F7 V2.1 TwinG Flight Controller |
MCU: 216MHz STM32F722 Gyroscope: 2x ICM20689 Barometer: NO Black box: 32 MB Betaflight OSD: YES BEC: 5V 2.5A / 9V 2.5A Current sensor scale: 100 Inverter for SBUS input (UART2-RX) Smartaudio & Tramp VTX protocol supported Beeper: Yes RSSI input field: No UART's: 5 Engine power: 8 8-pin 4-in-1 ESC connector (GND, VBAT, M1, M2, M3, M4, CUR, R5) DJI Air Unit 6-pin connector (R1,GND,R2,T2,GND,9V) BLHeli32 Telemetry: RX5 Input voltage: recommended 2-6S, MAX 8S Firmware target: IFLIGHT_F722_TWING Mounting pattern: 30.5*30.5mm Ø4mm with lugs Ø3mm Dimensions: 36x36mm Weight: 7.5g USB Type-C |
| SucceX 50A BLHeli_32 4in1 ESC | MCU: STM32F051 Up to a frequency of 48 kHz and PWM Capacitance: 470uF / 50V Current Sensor: Yes Input: 2-6S LIPO Constant: 50A / Burst: 60A BlHeli32 Telemetry: Yes BEEC: No Supports up to Dshot1200, Proshot, Multishot Destination: iFlight-BL32-4IN1 Weight: 14.4 grams Size: 43x39mm (including the power pads) Mounting Hole: 30.5 x 30.5mm / 3mm |
| XING 2806.5 1300KV / 1800KV motor |
Voltage: 2-6S
KV: 1300KV / 1800KV (Optional)
Configuration: 12N14P
Bearing: NMB 11*5*5
Stator diameter: 28
Stator Length: 6.5mm
Shank diameter: M5
Number of Cells (Lipo): 2-6S
Weight: 49.5 g (with a short cable)
Motor mounting hole: 19x19 φ3mm
|
| Gemfan 7040 3 blade propeller |
Quantity: 2 CW & 2 CCW Color may vary |
| SucceX Force 5.8G 800mW VTX |
Item: SucceX-Force 800mW adjustable VTX Input Voltage: 7-36V output voltage/max. Current: 5V 1A 12V input current: 40mA at PIT mode, 95mA at 25mA, 185mA at 100mW，250mA at 400mW, 380mA at 800mW Channel: 40CH Size: 36x36x3mm - PIT / 25mW / 100mW / 400mW / 800mW |
| Caddx Ratel 1200TVL FPV Camera | Brand Name: Caddx Item name: Ratel Lens: 2.1mm Image sensor: 1/1.8" inch Starlight HDR sensor
Horizontal resolution: 1200TVL FOV: 180 degrees Minimum. Latency: 8ms TV system: NTSC & PAL (changeable)
WDR: Super WDR (HDR)
Dimensions: 19x19x19mm Wide power input: DC 5-40V
Weight: 8g (NW) / 40.5g (GW)
|
| Optional receiver version |
PNP without receiver version: NOT included TBS CRSF Nano RX version: includes a TBS CRSF Nano RX |
| Lipo battery (NOT included) |
For 1300KV Version: Recommend 6S 4000-4500mAh Lipo Battery For 1800KV version: Recommend 6S 2600-3000mAh lipo battery |
Delivery content:
1x Chimera7 analog drone
1x TPU floor stand incl. locking screw (to install the TPU camera mount)
1x Caddx Ratel FPV Camera (built well on drone)
1x 5.8G 800mW VTX (Well built on drone)
1x 5.8G Albatross RP-SMA Antenna LHCP 150mm
2x Gemfan 7040 propellers CW
2x Gemfan 7040 propellers CCW
4x 20x250mm PU Leather Battery Strap (color may vary)